Zum Inhalt springen
Eltracore

ELKO EP

EMDC-64M

Herstellernummer
EAN
Preis auf AnfrageFragen Sie ein Angebot für dieses Produkt an.

Bestellung

Bestelleinheit
Stück

Beschreibung

The unit EMDC-64M is designed to control DALI electronic ballasts and DMX receivers from the iNELS system. EMDC-64M enables control of up to 64 independent electronic ballasts DALI (Digital Addressable Lighting Interface) for fluorescent lamps, LEDs and other light sources. EMDC-64M also enables connection of up to 32 receivers DMX (Digital MultipleX) in a single segment. When used repeaters can control up to 64 devices. Maximum amount of DMX controlled channels is 64 channels. Control from iNELS BUS System via EBM BUS. DIP switches on the front panel to select the control interface (DALI/DMX). Addressing of DALI ballast units can be done via the central unit and iDM3 software or via MINI USB on the front panel of the EMDC-64M and DALI Configurator software. The required functionality is set in user project in iDM3 software. The unit EMDC-64M is powered from the mains voltage 230 V AC. DALI BUS power supply is 16 V/250 mA via an EMDC-64M unit. The system BUS EBM is galvanically separated from the BUSes DALI/DMX. Terminals for connecting the DALI BUS are equipped with short circuit and surge protection. It is possible to connect up to 8 EMDC-64M units to one EBM BUS. If this concerns the last unit on a system BUS EBM, it is necessary to terminate the wire with a resistor with nominal resistance of 120 ?. The resistor is inside the unit, termination is made by shorting neighboring terminals TERM and EBM+. The BUS DMX must be terminated at its end by a resistor with nominal resistive value 120 ?. The resistor for DMX BUS termination is on the side of the EMDC- 64M inside the unit, termination is performed by shorting adjacent terminals TERM and A. Updating the firmware of the EMDC-64M can be done through the central unit adn software iDM3 or via MINI USB on the front panel and EMDC-64M Flasher software. Updating through MINI USB must be done while system BUS EBM is disconnected. When configuring DALI addresses two types are necessary to distinguished: - MASTER - this group includes sensors and detectors and one DALI branch can connect up to 4 DALI MASTER units • lighting intensity sensor DLS3-1 • motion detector DMD3-1 - SLAVE - electronic lighting ballast EMDC-64M in 3-MODULE design is designed for mounting in a control panel on a DIN rail EN60715.

Technische Daten

ETIM-Klasse: Bussystem-Dimmaktor (EC001094)

Communication

Bussystem KNX
Nein
Bussystem KNX-Funk
Nein
Bussystem Funkbus
Nein
Bussystem LON
Nein
Bussystem Powernet
Nein
Andere Bussysteme
sonstige

Options

Funk bidirektional
Nein
Busmodul abnehmbar
Nein
Leistungszusatz verwendbar
Nein
Parallel-Betrieb möglich
Ja

Model/type

Ausführung
Dimmaktor
Mit LED-Anzeige
Ja
Lastart
universal

Mounting/installation

Montageart
REG

Measurements

Breite in Teilungseinheiten
3
Min. Tiefe der Gerätedose
UN mm

Connection

Busankopplung inklusive
Ja
Nebenstelleneingang
Nein
Anzahl der Ausgänge
64

Setting/control

Vor Ort-/Handbedienung
Nein

Performance

Ausgangsleistung
0, 0 W

Electrical

Max. Steuerstrom
0 mA
Spannung
230, 230 V

Other

Frequenz
50, 60 Hz

Protection

Schutzart (IP)
IP20

Dokumente